I use a gasless mig, its harder to use and does take a little practice though, you need to ensure what ever your welding is as clean as possible, the key to a...
8971
sevenohms
Aug 19, 2011 11:11 am
I have a Cigweld that does both. Gasless is a waste of time, unless its a gate or something non structral, better off with a stick welder. On the other hand if...
8972
noel
grassy_noel2001
Aug 27, 2011 1:24 pm
Many thanks for all the relpies. I was just looking at wot people are using. Thanks for the information, i should have been more specific. I am old school and...
8973
Darren Trew
dr_falconstein
Sep 1, 2011 8:40 am
whats a 170 head worth these day ?...
8974
Early Falcon Club of WA
falconccwa
Sep 1, 2011 9:01 am
How long's a piece of string ? Just cost me $400 to have one reconditioned. To: earlyfalcons@... From: dtrew@... Date: Thu, 1 Sep...
8975
Ben Hobson
hqrace85
Sep 1, 2011 9:04 am
I spent $550 on mine, it was pretty bad Darren,Pretty sure I still have a 2nd hand 170 head that came off a runner about 12 months ago, it was only going to...
8976
undiesv8xp
Sep 19, 2011 1:04 pm
Brad, did you ever get a reply on your issue. I want to replace my hinges and don't know where to start. Do you take the door off ????? Andrew...
8977
Early Falcon Club of WA
falconccwa
Sep 19, 2011 11:41 pm
If you haven't done so already take a look at the Restoration Hint called Bush Whacked at our Club's website here -> ...
8978
Darren Trew
dr_falconstein
Sep 30, 2011 5:50 am
problem ! fuel gauge reads full when tank is almost empty why ? temp gauge is working ive cleaned all earth points on dash had one fule send "re calibrated"...
8979
Ben Hobson
hqrace85
Sep 30, 2011 7:54 am
Darren what does it read when tank is full Can you make the reading change if you pull the sender out of the tank and move the float up and down? ben...
8980
Early Falcon Club of WA
falconccwa
Oct 1, 2011 1:16 am
If you haven’t done so already check you these 2 Restoration Hints on our Club’s website 'Message Sender' and 'Gauging Response'. The latter will give you...
8981
Early Falcon Club of WA
falconccwa
Oct 1, 2011 1:27 am
Here's the link for the Club's Restoration Hints if you didn't have it. http://falconccwa.stormloader.com/hint.htm ... [Non-text portions of this message have...
8982
Darren Trew
dr_falconstein
Oct 8, 2011 11:12 am
ok dad took his XP to the auto electricians and the tested and found the fuel gauge is recieving 22 amp/volts !! how could this be happeneing?...
8983
Early Falcon Club of WA
falconccwa
Oct 9, 2011 12:26 am
I'd suggest that if the auto electrician found nothing else wrong the multi-vibrator voltage regulator that is housed in the temp gauge is not functioning...
8986
xp289w
Nov 2, 2011 10:56 pm
Hi Guys has anyone installed baby seats in an xp coupe? if so where did you anchor it? our little one still not an age to face front forward so the seat...
8987
xp289w
Nov 2, 2011 11:31 pm
Hi Guys i had to change sign up again to yahoo my xev8 user ID had been disabled or something, anyway, i finaly had the Castlemaine Rod Shop brake conversion...
8988
Ben Hobson
hqrace85
Nov 3, 2011 1:23 am
Mick best bet would be to go to a child restraint fitter and seek their advice Ben...
8989
graham
louypan05
Nov 15, 2011 8:17 am
Hey guys, Anyone got a working horn they wish to sell? The other day mine locked on in the heat when I wasn't home and fried its internal organs! Regards,...
8990
xp289w
Nov 29, 2011 12:03 am
Hi guys I'm looking at putting the venetian back in the coupe for the summer but it is in need of a respray, it's an original steel one. For the XP's what were...
8992
earlyfalcons
Dec 10, 2011 11:29 am
an off whitish, all ones I have seen in cars are a gloss. Deon...
8993
Michael Carbone
xp289w
Dec 11, 2011 8:07 pm
Cheers To: earlyfalcons@... From: earlyfalcons@... Date: Sat, 10 Dec 2011 11:29:05 +0000 Subject: [Early Falcons] Re: venetian blinds...
8995
willieplumah
Dec 19, 2011 5:04 am
1966 Ford Falcon XP Rego # JOJ 320 Engine # D33914S Vin # D339148 Drive type - rear Original 6 Cylinder 170 c/inch (2786cc) pursuit engine 3 speed Manual (with...
8996
dale@...
dale_westlake
Dec 19, 2011 9:33 am
so what are you chasing? and where are you,state ect? Dale ... From: willieplumah To: earlyfalcons@... Sent: Monday, December 19, 2011 3:04 PM ...
8997
xk72js
Jan 23, 2012 8:00 am
Hi All, New to the forum and I have a question for you all. I am aware that Ford Australia owns the first Falcon off the production line. Other than that car -...
8998
xmfordfalcon
Jan 28, 2012 8:45 am
Sorry if this has been covered before guys. I am thinking of converting my 144 powered XL to a 170 pursuit with alternator already fitted. My question is in...
8999
xmfordfalcon
Jan 28, 2012 10:35 pm
Doesnt matter which way I look at the photo, the thick black wire seems to be at the wrong end?...
9000
xmfordfalcon
Jan 28, 2012 11:05 pm
To be honest Im getting the impression that someone has retrofitted this style regulator as I cant seem to find any info on it ever being fitted to an early...
9001
Early Falcon Club of WA
falconccwa
Jan 29, 2012 12:42 am
Just to double check, has the alternator on 170 motor got in internal voltage regulator or is it the original alternator that uses and external voltage...
9002
xmfordfalcon
Jan 29, 2012 6:51 am
wow thankyou for the in-depth reply. I was kind of thinking along the same lines. Just wasnt sure if I was looking at it the wrong way or anything. Seems...
9003
Early Falcon Club of WA
falconccwa
Jan 30, 2012 12:25 am
The Alternator on the 170 motor is one with an internal Voltage Regulator so the wiring method shown at the Club's website will work with this model. The...
