there's that place in jasper road that seems to score some very cool car clients. Must be a reason for that I figure. *Bentleigh Garage* 187 Jasper Road,...
Good afternoon, My parents own a 65 XP Coupe and are looking for a Split Bench front seat. Does anyone know anywhere/ anyone that is selling parts for an XP by...
Hi I took out my old roof lining yesterday and this was tucked up inside. I thought people may be interested. Does anyone know if all XPs have this piece of...
leif, no pic but i’m assuming you’ve got the production line build sheet, never seen one in an aussie falcon, and i’ve dismantled several hundred of...
and then i looked at the heading............ paint inspection record! haven’t found one of these either! From: John Longworth Sent: Saturday, September 01,...
Hi all, I had a bit of a stack on the weekend and am now looking for a passenger front guard for my XL falcon. Also a grille and a front bumper. I am in...
Hi Guys i need to fix my quarter vent window and need to remove the door trim on the 2 door. So... after removing the window winder and armrest, how do i take...
If you have the lower chrome trim along the bottom of the door panel (it’s unlikely) pull the door panels from the middle sides. If the lower chrome trim is...
Thank you ! I'll give that a go I have that chrome strip at the bottom of my door trim still it's not in the best condition but still there can u not get new...
We haven't seen any 'After Market' ones but some of our members have had them folded and plated locally. ... [Non-text portions of this message have been...
I have stainless steel lower door moldings available for the coupes, same shape as original and wont rust ! Once polished look as good as chrome. Deon...
Hi all, My XP sedan drivers door glass keeps dropping out of the channel at the bottom that supports it. I have glued the glass into the channel a few times...
Try replacing the rubber sleeve in between the channel and the glass with a length of 50mm wide truck inner-tube. You will have the take the glass and the...
Hi Guys it would be good to find out who HAS success in keeping an xm/xp v8 cool in 30+ degree heat while stuck in traffic ONLY as keeping it cool on the go is...
Try a glue pretty sure it's called sicaflex it holds metal to glass I used it on and old Lancer to glue together a rusty channel to a window lasted for the...
Hi Mick ? I think, I have an XP with 302 efi motor, running XB 3 row radiator with EB twin electric fans behind radiator- cut plastic shroud to somewhat fit...
Hi Matt yeah hit the revs up and it comes down, i have to seal my shroud abit better and im getting a fration smaller water pump pulley to spin it a little...
XM V8 Coupe, single core Aluminium radiator, twin 10" (I think) thermo fans positioned on the engine side of the radiator with the wiring reversed so they pull...
hi guys, my opinion, from 30 years experience playing with these cars, beware of fitting the smaller pulley,it also increases coolant speed at high revs!...
Thanks John, my crank pulley is 150mm in diameter same with the current water pump pulley I have a 135mm water pump pulley from a 65-66 mustang that had either...
One thing I forgot to mention and I'm assuming an issue that after I turning the car off after its had a good run there is the slightest of noises from the...
It is normal for the cooling system to build up heat/pressure after the engine is turned off (hence the invention of overflow bottles) but the cap should seal...
Another thing, also make sure your idle isnt set too high. Mine at 1000rpm (Chokeless Winter Setup) on a hot day gets warm very quickly at the lights, bump it...
Well after 47 years, the stock drivers window winder has given up the ghost and lost too many teeth to drive the window. What are my options guys? Is there a...
what kills the quadrent, is the bush on the inner end of the winder spindle, it wears,allowing the teeth to come out of mesh,then chews the ends off, you can...
