Put a mark on the drum or hub on the outer edge and turn the pinion yoke while getting someone to watch the hub mark. If you turn the pinion nearly 3 times for...
Hi Damien, The P I am bringing back to the road had a vinyl roof, fitted at the factory... The car was originally owned by Leylands 'Experimental Engineering...
Hi Damien, I know that the vinyl roofs were added by the dealers in Qld. Cheers Adrian ... __________________________________ Start your day with Yahoo! - Make...
Thanks for your comments John. Im not trying to build a 21st Century Rocketship, just a fairly rapid 70s GT but as a P76. Actually my interpretation of the...
Hi everyone, I have seen a couple of people determine what diff ratio they have by turning the axel and watching the center drive yoke. I have a diff under the...
... able to do much better, lower weight greater power to weight. Steve I like your set up pretty much bullet proof and it should be fun to drive. Who are...
For those Victorians out there than may know Morgan he is getting married on Saturday at Wonthaggi. That wonderful partner of his is finally making an honest...
I thought I would throw my 2cents worth in. I am current restoring my Exec with a few changes. I also was looking for something a bit sportier. After much...
Hi all; Two questions: 1. Were vinyl roofs a factory option ? 2. Has anyone written an article on compliance plates and codes for any of the club magazines...
All good info, thanks i'll have to do a bit more planing . As for the th700 ive got it now and will use it soon. After the b/w 35 dramas im not going back...
Thanks Daivd, im going to the 4 speed overdrive so thats why the 3.89 was a cheep option. I got a quote for 3.23 gears(new) it was $ 589.00) I just wasnt sure...
A couple of things you've got to consider: 1) Torque, these motors are full of it from relatively low revs, compared to the GEN IV some 1500 rpm lower for peak...
Yes get out the calculator,17 inch low profile wheels add stuff all.,3.23,3.45,3.7 might be better.modern holden runs 3.08 stock and has a very tall...
guys, is it possible to put the 3:89 gears from a six diff into a v8 lsd ? Was talking to a diff guy and as im running 17" rims and 265 x 45 rear tyres the...
hi all me again can anyone tell me if there is a dealer in perth who can supply a inlet manifold for my v8 4.4 that will take a 4 barrel carb. i think i have...
I thought the idea was to order parts we needed not waste Fred's time with ridiculous requests for Body Shells and complete set of body panels. While I won't...
Hi John. I have not heard from him directly but i have heard from 2 sources that some of the requests have been a little out of the ordinary ie a new body...
Has anyone any idea where things are at with parts that many have put an order in with Fred months ago? I know we have been asked not to contact him directly...
Thanks again, now i realise making the plate will not be an option. Ive emailed garth just waiting for a reply on his plate. As for setting up the kickdown...
Hi - Just finished the Victorian concourse ( long , but good day for me ) I have a substantial collection of motoring magazines ( predominantly modern motor,...
It is 3 parts not just the plate...... alloy plate,converter adapter ring,crank centering bush + countersunk screws etc,etc, i converted my p76 c/member to...
Leyland P76 Articles Please note it is a MS word table based doc. I have yet to go through my magazine collection to identify what I have, I am currently...
I am have started to develop a data base of the articles associated with the P76 and its derivatives such as a V8 engined Kimberley and the V6 and 6 cylinder...
Hi Niko I thought it was you that won the trans,and it wasa good price.But like anything s/hand, consider it only parts value until it is proven.If you contact...
