You can set the sort order of messages. Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
The regulator/rectifier is mounted behind the left hand side cover (as you are seated on bike) its the metal box with the fins that is held on with two Allan...
Ok, so I pulled the rectifier and cleaned all the wiring. I then charged the battery and started her up. Got a reading of 13.8 and stayed there. Now all I...
Howdy All I just finished recovering my seat last night. It was a lot easier than I first thought it would be. Cost me a whole $8. First remove the old torn...
Hey Scott, it looks as though you will be on the road in no time. I recovered my seat too only a couple of weeks ago and I got my vinyl from Spotlight as well....
Hi all. As promised to Brian I have finally gotten down to Peter Stevens and enquired about a full carby kit for the GS250FW. I was told that they dont come in...
That's great news Mark and I appreciate the effort. I will wait for John to post the information on part numbers. I assume we can order thru any one of the P....
Hi John, just a quick question before I post you the carby parts list. After getting home I had a really close look at the list and I found that the schematic...
Mark, It appears the GS250T (apparently also known as the GSX250T outside of the USA) is an air cooled twin so is very different from the GS250FW and GF250. ...
Howdy All Anyone know what forks I can substitute to suit the GS250FW? Mine have a nice bend in both sides and too many small nicks to seal properly. I just...
love the site and the email's i get about the gf250. wondering if anybody knows where i can track down a roadworthy frame for a gf20s. i t boned a tray ute and...
Hey peoples, I'm new to motorcycles in general and while shopping around one of mates remembered he had an old bike in the shed. Turns out it's a GS250FW, and...
Hi. These bikes aren't worth too much, maybe AU$1500 running, in reasonable condition and registered if you were to sell it. Parts can also be difficult to...
After a series of flat batteries and some basic trouble-shooting of the electrical system it appears that the VR on my biike is buggered. I can't get a voltage...
G'day All I am currently putting the pieces of a gf250s. I have a question about the carbies, hopefully someone can put me straight. I am wondering where to...
One line goes from the float bowl to the gas tank on/off valve and the other is the air or vacuum line. At least I think I remember that correctly. Haven't...
Have most parts, except rear suspension, wheel. Bike had 20,000km, but I cut it in half with a grinder, front half incl motor/gearbox intact. some fairing and...
Hi everyone, Hope that everyone's had some goiod times on their bikes recently. I've finally got my gf on the road and registered. Its great fun as well...
The fork seals aren't that hard to do. It is a messy job to say the least. Get GOOD quality fork seals. This is a must. The cheap ones are well cheap. I...
For Casper James: I would be interested in a couple of Carbs. Are the ones you have any good? Just need new jets but can't seem to find them anywhere and the...
The places you speak of sound like America, sorry, those parts are allready spoken for. ... -- ROBBO [Non-text portions of this message have been removed]...
Hi, my 87 GF 250 is down on power and I suspect the compression is low. Anyone experience of how much I am in for to do rebore and new pistons and rings? The...
Greetings all, Could someone please tell me what spark plugs go into an 84 GF250? I've checked the workshop manual which says NGK D9EAs, but the ones I pulled...
You should use D9EA or if your motor has a few miles on it you can use D8EA which are one heat range hotter. (I use these) C8HSA is incorrect and should not be...
