Hello all. I am in desperate need of a cam chain tensioner. If anyone knows of where i can get one, please let me know. I have been told part is no longer...
I'm doing a slight reco on the engine on my 84 gs250fw. anyone know if parts and gaskets are herd to come by?? The couple local places (i'm in rural nsw) don't...
Hey all, I've just bought an 84 GS250FW which has been stood in some guys garden for years, and im wondering if anyone here can give me a little advice. I have...
Greetings all, Could someone please tell me what spark plugs go into an 84 GF250? I've checked the workshop manual which says NGK D9EAs, but the ones I pulled...
Hi, my 87 GF 250 is down on power and I suspect the compression is low. Anyone experience of how much I am in for to do rebore and new pistons and rings? The...
For Casper James: I would be interested in a couple of Carbs. Are the ones you have any good? Just need new jets but can't seem to find them anywhere and the...
Have most parts, except rear suspension, wheel. Bike had 20,000km, but I cut it in half with a grinder, front half incl motor/gearbox intact. some fairing and...
Hi everyone, Hope that everyone's had some goiod times on their bikes recently. I've finally got my gf on the road and registered. Its great fun as well...
G'day All I am currently putting the pieces of a gf250s. I have a question about the carbies, hopefully someone can put me straight. I am wondering where to...
After a series of flat batteries and some basic trouble-shooting of the electrical system it appears that the VR on my biike is buggered. I can't get a voltage...
Hey peoples, I'm new to motorcycles in general and while shopping around one of mates remembered he had an old bike in the shed. Turns out it's a GS250FW, and...
love the site and the email's i get about the gf250. wondering if anybody knows where i can track down a roadworthy frame for a gf20s. i t boned a tray ute and...
Howdy All Anyone know what forks I can substitute to suit the GS250FW? Mine have a nice bend in both sides and too many small nicks to seal properly. I just...
Hi all. As promised to Brian I have finally gotten down to Peter Stevens and enquired about a full carby kit for the GS250FW. I was told that they dont come in...
Howdy All I just finished recovering my seat last night. It was a lot easier than I first thought it would be. Cost me a whole $8. First remove the old torn...
Howdy All Does anyone have a better, clearer copy of the wiring diagram for the GS250FW? I am trying to clean up my wiring but am finding it difficult to read...
I have had my GS250FW in pieces for so long that I can't remember when it was running last. I finally stripped the carbs, painted the frame and exhaust and...
Hey All I'm looking at putting some new rubber on my GS250FW but not sure what size. On the bike now are Front 100/90/16 Rear 110/90/18. The workshop manual...
hey guys, just thought I would post and let you know that I have finally finished my bike and I got a roadworthy certificate today (YAY) and it is booked in at...
Hey people. Is there any one out there looking for decals for their GS250FW? After getting my bike ready for a respray I began searching for decals and found...
Hey People. Are there any other GS250FW owner/riders out there in the Melbourne area. It might be nice to get a few people together and go for a ride...
Hey Remminga, Can you tell me where the Melbourne dealer is and some contact details for the same. I also own a GS250FW that I am rebuilding and most of the...
Howdy: I a have a GS250FW (84-86?)that needs a monoshock and fork seals. Searching on line, even in England, doesn't seem to generate anything. I am back home...
Hey all. I've just got my bike license and bought a '84 gs250fw. Are they supposed to be gutless between 5500-8000rpm?? If the revs go below this (at highway...
